Yoda, one of the principal characters in the “Star Wars” movie series, would be proud of you. One of his famous quotes — “Do or do not. There is no try.” — resonates with me when it comes to attempting a project around the home. Most jobs are not that hard. Often it’s just a matter of having the needed tools to guarantee success.
To replace a toilet, you often just need a few simple tools. My guess is you have an adjustable wrench, a putty knife, a 2-foot level, a screwdriver and a hacksaw. This is often all you need for this project.
The first step is to turn off the water supply to the toilet. You should have a small valve under the toilet that controls the flow of water. If not, you may have to turn off the water supply to the entire house. Check that the water is off by flushing the toilet one final time. If the water is off, no water should enter the toilet tank.
Pour four gallons of fresh water into the toilet bowl as fast as possible to get as much water out of the toilet bowl as possible. Use the putty knife to remove the decorative caps that hide the bolts that secure the toilet bowl to the hidden toilet flange under the toilet. Disconnect the flexible water supply line from the base of the toilet tank. Remove the nuts from the toilet bolts.
You’re now ready to lift the toilet off the floor. You may have to rock it side to side to break any bonds with tile grout or caulk that should be between the toilet and the flooring. Once you have the toilet in the air, carry it outside with a helper. Don’t set it down on any good carpet or other finished flooring, because nasty wax from the toilet seal could permanently stain whatever it touches.
The next step is to clean the existing toilet flange. If a wax gasket was used before to seal the toilet to the flange, you should scrape off any excess wax and otherwise clean it up. Set aside about a tablespoon of the best wax. You’ll need it in a few minutes. I’d wear disposable gloves for this part of the job.
The next steps are critical for a professional installation. You get but one chance to set the toilet down on the flange. You can’t, or shouldn’t, move the toilet once you press it down into the fresh wax gasket. If you do monkey with the toilet, trying to make adjustments, you risk breaking the all-important seal.
This means you need to dry-fit the toilet bowl to the floor without the new wax gasket in place. Put the toilet on the flange and level the bowl both left and right and front to back. Place wood shims as required to get the toilet level. Tape these shims tightly to the finished floor so they don’t move when you lift the toilet back up.
Place the wax gasket on the toilet flange. I prefer to use gaskets that come with a small plastic horn that forces the toilet water and waste down into the piping below the toilet flange. Install new toilet bolts and use some old wax from the previous flange to help hold them vertical in the toilet flange slots.
Straddle the toilet flange and have a helper guide you to lower the toilet bowl slowly so the toilet bolts line up with the holes in the base of the toilet bowl. Remember, you only get to set the toilet down one time. Be sure the toilet bowl is square to the wall so you don’t have to twist it excessively. A helper at this stage of the installation is invaluable since you’re a rookie.
Be sure the toilet bowl is tight against the wood shims. Install all the new parts for the decorative toilet bowl caps and tighten the nuts. Resist the urge to apply vast amounts of force to tighten the nuts to the bolts. While the china is strong, some people have cracked the bottom of the bowl by using too much force.
Install the tank to the bowl according to the instructions and install a new water supply line. You can now test the toilet to see how well it works. Turn on the water supply valve, and the toilet tank should fill with water. Flush it and see how it all works.
If all is well, it’s now time to grout the toilet bowl to the floor. Do not use caulk for this. The connection between the toilet bowl and the floor needs to be a solid material like grout that will not flex when it’s dry. You want the toilet to be rock solid to the floor so it never rocks back and forth. Rocking will eventually break the seal between the toilet and the toilet flange.
Don’t let the grout touch the wood shims. After about 15 minutes, gently remove the wood shims and use the mixed grout to fill in the voids created by the missing shims. Don’t sit on the toilet for at least eight hours so the grout has a chance to harden.
Need an answer? All of Tim’s past columns are archived for free at www.askthebuilder.com. You can also watch hundreds of videos, download Quick Start Guides and more.